Laser Engraver Blogs

During the engraving process, your Ray5 machine may occasionally display alarms or errors. These alerts are typically related to limit switches, coordinate settings, or user operations.

This guide explains the most common causes of engraving errors and provides clear solutions to help you quickly resume normal operation.

Common Causes & Solutions

1. Manual Movement During Engraving

Cause:
Manually moving the laser head or gantry while the machine is engraving can trigger the limit protection system.

Solution:

• Avoid any manual interference during operation
• Always pause or stop the job properly before adjusting the laser position

 

2. Alarm After Pressing “Stop”

Cause:
Clicking the Stop button during engraving may trigger an alarm signal. This is normal system behavior.

Solution:

• No action required
• Simply reset or restart the job if needed

 

3. Overscan Triggering Soft Limits

When engraving an image or vector filling at the current position, if the overscan function is turned on, the soft limit may be triggered, and the engraving may not be possible. You need to change the coordinates to absolute coordinates. If you do not change the coordinate system, then reduce the pattern and put it in the middle, or turn off the overscan function.

4. Limit Switch Signal Abnormality (Homing Issues)

The machine continuously detects the signal of the limit switch, resulting in a zeroing abnormality. The solution is to confirm that the XY axis does not hit the limit switch after the XY axis completes zeroing.

Additional Tips

• Always verify coordinate mode and workspace boundaries before engraving
• Avoid placing designs too close to the edges of the working area
• Regularly inspect limit switches and wiring for reliability

Conclusion

Most engraving errors or alarms on the Ray5 are caused by limit triggers, coordinate misconfiguration, or normal operational behavior. By understanding these common scenarios and applying the appropriate fixes, you can quickly resolve issues and maintain smooth engraving workflows.

Proper setup and careful operation will significantly reduce the occurrence of alarms and improve overall efficiency.

If the X-axis or Y-axis motor on your Ray5 laser engraver is moving in the opposite direction than expected, it can lead to incorrect positioning, failed engraving, or even machine errors.

Motor direction is controlled by both hardware wiring and software/firmware signals. To fix a reversed motor, you only need to adjust one of these elements so that they match correctly.

This guide provides three effective methods to correct motor direction, from the easiest (software) to the most advanced (hardware).

Core Principle

Motor rotation direction is determined by:

• Motor wiring sequence → Physical wiring defines the default rotation
• Direction control signal → Software/firmware instructs the driver on movement direction

To fix a reversed motor, you align the control signal with the wiring direction.

Step 1: Adjust Software Settings (Quickest Method)

This is the easiest and safest method.

In your control software (e.g., LightBurn):

1. Open Device Settings or Machine Settings
2. Locate Axis Mapping or Motor Direction options
3. Find options such as:
   • “Invert X Axis”
   • “Invert Y Axis”
   • “Reverse Direction”
4. Check (or uncheck) the axis that is moving in the wrong direction
5. Save the settings
6. Use jog controls to test movement

✅ If the direction is now correct, no further steps are needed.

Step 2: Adjust Firmware Settings (Advanced / Reliable Method)

If software settings are insufficient, modify firmware parameters directly.

Using G-code commands (via LightBurn or LaserGRBL):

1. Connect the machine to your computer
2. Open the Console / Terminal window
3. Use the following GRBL parameter:

• $3 – Direction invert setting

How it works:

• Each axis direction is controlled by a binary value
• Setting the parameter to true inverts direction

Examples:

• Reverse X-axis → set X direction invert to true
• Reverse Y-axis → set Y direction invert to true

⚠️ Tip: If the motor is reversed, simply toggle the setting (true/false) until the direction is correct.

4. Save the changes
5. Test using jog controls

Step 3: Hardware Adjustment (Physical Solution)

If software and firmware adjustments do not resolve the issue:

Reversing Motor Wiring

1. Power off the machine completely
2. Locate the motor cable of the reversed axis
3. Swap any one pair of wires:
   • A+ ↔ A−
   • or B+ ↔ B−

This will physically reverse the motor rotation direction.

4. Reconnect and power on the machine
5. Test the axis movement

Important Notes

• Always try software settings first before modifying hardware
• Ensure the machine is powered off before any wiring changes
• Avoid changing both software and hardware simultaneously—adjust one at a time

Conclusion

Motor reversal on the Ray5 is a common but easily fixable issue. In most cases, it can be resolved through simple software configuration changes. For persistent cases, firmware or hardware adjustments provide a reliable solution.

By following the steps outlined above, you can quickly restore correct axis movement and ensure accurate engraving performance.

The flame sensor and motion sensor are important safety features designed to protect your engraving process. However, they can sometimes be triggered unintentionally due to environmental factors, incorrect settings, or hardware issues. This guide will help you identify and resolve common alarm problems.

Flame Sensor Alarm

The flame sensor can be easily triggered. When it is activated, the LightBurn console will display Alarm 3. This can happen for several reasons, including ignition during use, strong light exposure, incorrect settings, short circuits, or even sensor damage.

To avoid unnecessary alarms, it is important to maintain a proper working environment. Avoid open flames during engraving. If an open flame occurs, reduce the laser power immediately to prevent triggering the sensor.

Environmental lighting also plays a role. The engraving machine should be placed in a normal indoor environment and kept away from strong light sources such as flashlights or direct sunlight, as these can interfere with the sensor.

If the flame sensor is still triggering, you can adjust its sensitivity. Open LightBurn or LaserGrbl, connect your machine via USB, and enter the following command in the control panel:

This command lowers the flame sensor trigger threshold. If the issue continues, you can further reduce the value until the sensor behaves normally.

In some cases, the issue may be caused by a hardware contact. If the flame sensor is triggered at the beginning of engraving, check whether the sensor’s metal pins are touching the metal casing. The flame sensor is a black cylindrical probe located at the back of the RAY5 control box. Carefully adjust its position to prevent contact.

If necessary, you can temporarily disable the flame sensor by entering:

To enable it again, use:

Motion Sensor Alarm

The motion sensor is designed to detect unexpected movement during operation. However, it may also trigger due to machine instability, incorrect settings, or sensor issues.

Make sure your engraving machine is placed on a stable and level surface. Any vibration or movement during operation can cause the motion sensor to activate.

If the sensor is too sensitive, you can adjust its trigger threshold through software. Open LightBurn or LaserGrbl, connect your machine via USB, and enter the following commands:

These commands reduce the sensitivity of the motion sensor and help prevent false alarms.

If the motion sensor continues to trigger at the start of engraving, it may indicate a hardware issue. In this case, you can disable the motion sensor by entering:

To turn it back on, simply send:

Conclusion

Flame sensor and motion sensor alarms are usually caused by environmental interference, overly sensitive settings, or hardware-related issues. Most problems can be resolved by adjusting settings, improving the working environment, or checking hardware connections.

By following the steps above, you can quickly restore stable operation and ensure safe and reliable engraving performance.

If your laser engraving machine stops unexpectedly during operation, the issue is often related to software, connection, electrical, or hardware factors. This guide covers the most common problems and practical laser engraver troubleshooting steps to help you quickly identify and fix the issue.

I. Software and Connection Issues (Most Common)

1. Data Transmission Interruption (USB Cable Issues)

Cause:
This is one of the most common reasons for a laser engraving machine stopping mid-job. Poor-quality USB cables, loose connections, long cables, or signal interference can interrupt data transmission.

Troubleshooting:

• Reconnect both ends of the USB cable (computer and engraver)
• Use a high-quality, shielded USB cable and keep it as short as possible
• Keep the USB cable away from power cables and motor wires to reduce interference
• If using a network connection, ensure stable network performance

2. Computer or Software Issues

Cause:
Low system performance, software freezing, or conflicts with other programs can interrupt LightBurn or LaserGRBL jobs.

Troubleshooting:

• Restart the software and computer
• Check power settings to ensure the system is not in “Power Saver” mode
• Reduce data output speed in your engraving software (e.g., LightBurn). If the output frequency is too high (above 20 kHz), lower it to improve stability
• Open Task Manager to monitor CPU and memory usage during operation

3. File or Design Issues

Cause:
Overly complex designs, excessive nodes, or corrupted G-code files can cause engraving to stop.

Troubleshooting:

• Optimize your design using vector tools like “Combine” or “Simplify Path”
• Remove stray points or unnecessary details in the design file
• Re-export or regenerate the G-code file

II. Electrical and Hardware Issues

1. Power Supply Problems

Cause:
An unstable or insufficient power supply can cause laser engraver interruptions or resets.

Troubleshooting:

• Ensure all power plugs are securely connected
• Verify the voltage switch (110V / 220V) is set correctly
• Avoid sharing a power source with high-power appliances that may cause voltage drops

2. Overheat Protection

Cause:
Overheating of the laser module, motor drivers, or mainboard may trigger automatic shutdown for safety.

Troubleshooting:

• Check that all cooling fans are functioning properly
• Ensure proper ventilation in your workspace
• Avoid high ambient temperatures during operation

3. Motor Stall or Step Loss

Cause:
If movement is blocked or the load is too heavy, the motor may lose steps and trigger an emergency stop.

Troubleshooting:

• Check belt tension and guide rail condition
• Clean and lubricate the rails regularly
• Remove any obstacles blocking movement
• Reduce motor acceleration settings in your engraving software for smoother motion

4. Limit Switch False Trigger

Cause:
A false trigger from the limit switch can cause the machine to stop or reset unexpectedly.

Troubleshooting:

• Check if the limit switch lever is loose or misaligned
• Inspect wiring for damage or short circuits
• Manually move the laser head to check for premature triggering

III. Control Board and Firmware Issues

1. Control Board Malfunction

Cause:
A malfunctioning control board may be due to aging components, electrical damage, or static interference.

Troubleshooting:

• Observe indicator lights on the control board for abnormal behavior
• Restart the machine to reset the system
• Update or refresh the firmware if possible

Conclusion

When your laser engraving machine stops during operation, the issue is usually caused by one of the following:

• USB connection or data transmission issues
• Software or file-related problems
• Power supply instability
• Hardware issues such as overheating or motor stall
• Control board or firmware errors

By systematically following these laser engraver troubleshooting steps, you can quickly identify the root cause and restore stable operation.

Over time, dust, smoke residue, and debris can accumulate on the laser window lens and nozzle of your Ray5 mini or miniS. This buildup can reduce engraving quality, weaken laser output, and even affect cutting performance.

Regular cleaning helps maintain optimal performance and extends the lifespan of your laser module. This guide provides a safe and effective step-by-step cleaning process.

Tools Required

• Microfiber cloth or lint-free paper towel
• Alcohol (preferably isopropyl alcohol)
• 2mm Allen wrench
• (Optional) Soft cleaning brush or air blower

Step-by-Step Instructions

1. Remove the Laser Module

• Disconnect the laser cable
• Loosen the M3×14 screws or 7-shaped thumbscrews
• Carefully remove the laser module from the machine

 

Ray5 mini/miniS 2.5/3.5W 

Ray5 mini/miniS 5.5/10W

2. Remove the Nozzle

• Use a 2mm Allen wrench to loosen the four mounting screws
• Remove the nozzle carefully

Special Note:

• For 2.5W / 3.5W laser heads, the nozzle is magnetic and can be removed directly

 

3. Clean the Lens and Nozzle

• Lightly moisten a microfiber cloth or paper towel with alcohol
• Gently wipe:
  • The laser window lens
  • The acrylic part of the nozzle

⚠️ Important:

• Do not use excessive liquid
• Avoid scratching the lens surface
• Use gentle pressure only

 

4. Reinstall the Nozzle

• Reattach the nozzle to the laser module
• Ensure correct orientation:
  • The side with the notch should face the back of the laser
• Tighten the screws or ensure magnetic alignment is secure

5. Reinstall the Laser Module

• Mount the laser module back onto the machine
• Reconnect the laser cable
• Ensure all connections are secure before powering on

Mini:

MiniS:

Conclusion

Cleaning the laser window lens and nozzle is a simple but essential maintenance task that directly impacts engraving quality and machine performance. By following the steps above, you can ensure your Ray5 mini/miniS operates with optimal precision and efficiency.

Regular maintenance will help maintain consistent output and prolong the life of your laser module.

 

The laser fan plays a crucial role in cooling the laser module during operation. A malfunctioning or noisy fan can lead to overheating, reduced engraving performance, or even hardware damage.

This guide explains how to safely replace the laser fan on different Ray5 mini/miniS models to ensure proper cooling and stable performance.

Tools Required

• 2mm hex wrench
• Replacement laser fan
• Small container (for storing screws and washers)

Step-by-Step Instructions

1. Ray5 mini/miniS 2.5W / 3.5W

① Remove the Fan

• Use a 2mm hex wrench to loosen the screws
• Be careful to keep the four 1mm black washers (do not lose them)

 

② Disconnect the Cable

• Unplug the fan cable from the mainboard
• Carefully remove the fan

 

③ Install the New Fan

• Route the new fan cable through the lower-left corner
• Connect the cable to the mainboard

④ Secure the Fan

• Place the four washers between the fan and the frame
• Tighten the screws to secure the fan in place

 

2. Ray5 mini/miniS 5.5W / 10W

① Remove the Fan Assembly

• Use a 2mm hex wrench to loosen the screws
• Carefully remove and keep track of:
  • Four 8mm standoffs
  • Four 12mm standoffs

 

② Disconnect the Cable

• Unplug the fan cable from the motherboard
• Remove the fan

 

③ Install the New Fan

• Install the new fan in position
• Connect the fan cable to the motherboard

 

④ Cable Routing

• Route the cables along the profile groove
• Ensure the fan cable is positioned at the back of the laser module

⑤ Reassemble the Structure

• Place the 8mm standoffs between the fan and the motherboard
• Place the 12mm standoffs between the motherboard and the transparent acrylic panel
• Secure all components with screws

⚠️ Make sure the transparent acrylic panel is correctly oriented to align with the laser module connector

Mini:

MiniS:

Conclusion

Replacing the laser fan is an important maintenance task to ensure proper cooling and stable operation of your Ray5 mini/miniS. By following the correct installation steps for your specific model, you can restore efficient heat dissipation and maintain optimal engraving performance.

Regular inspection of the fan and cooling system helps prevent overheating and extends the lifespan of your laser module.

The laser window lens is a critical optical component that protects the laser module while allowing the laser beam to pass through with precision. Over time, the lens may become scratched, dirty, or damaged, which can lead to reduced engraving quality or power loss.

Replacing the lens when necessary helps maintain optimal engraving performance and ensures consistent results.

Tools Required

• M2 hex wrench (for 10W models)
• Replacement laser window lens
• Clean workspace (to avoid dust contamination)

Step-by-Step Instructions

1. Remove the Laser Protective Cover

• For 2.5W / 3.5W / 5.5W models:
  • Directly remove the protective cover
• For 10W model:
  • Use an M2 hex wrench to loosen the screws securing the protective cover
  • Carefully remove the cover

 

2.5W/3.5W 

10W

2. Remove the Old Lens

• Gently unscrew the window lens by turning it counterclockwise
• Carefully take out the old lens
• Avoid touching the lens surface directly to prevent contamination

 

2.5W/3.5W                    10W

3. Install the New Window Lens

• Align the new lens properly with the mounting threads
• Gently screw it in by turning clockwise
• Do not overtighten—firm is enough to ensure a secure fit

4. Reinstall the Protective Cover

• Place the protective cover back onto the laser module
• Secure it using screws (for 10W models)
• Ensure everything is properly aligned and tightened

Mini:

MiniS:

Conclusion

Replacing the laser window lens is a simple yet essential maintenance procedure that helps maintain engraving clarity and laser efficiency. By following the correct steps, you can ensure your Ray5 mini/miniS continues to deliver high-quality and stable performance.

Regular inspection and timely replacement of the lens will significantly extend the lifespan of your laser module and improve overall output quality.

The laser module is the core component of the Ray5 mini/miniS engraving system. Over time, laser modules may need to be replaced due to wear, reduced output, or damage.

Different wattage versions use different mounting structures, so it’s important to follow the correct procedure for your specific model to ensure safe and proper installation.

Tools Required

• Screwdriver / hand tools (M3 screws or L-shaped screws)
• Replacement laser module
• Clean workspace

1. Ray5 mini/miniS 2.5W / 3.5W

① Remove the Old Laser

• Unplug the laser cable
• Loosen the M3×14 hand screws
• Carefully remove the laser module

② Install the New Laser

• Align the plastic mount on the back of the laser with the X-axis frame
• Slide the module down vertically into position
• Tighten the hand screws securely
• Reconnect the laser cable

 

2. Ray5 mini/miniS 5.5W / 10W

① Remove the Old Laser

• Unplug the laser cable
• Loosen the L-shaped hand screws
• Remove the old laser module

② Transfer the Dovetail Rail

• Loosen the screws on the back of the laser
• Remove the dovetail rail from the old module
• Install the dovetail rail onto the new laser module

 

Mini:

MiniS:

Conclusion

Replacing the laser module on the Ray5 mini/miniS is a straightforward process when following the correct steps for each wattage type. Proper installation ensures stable performance, accurate engraving, and optimal laser output.

Regular maintenance and timely replacement of the laser module help extend the machine’s lifespan and maintain consistent engraving quality.

The X-axis and Y-axis motors are essential components that drive precise movement during engraving. If the motor becomes faulty, you may experience issues such as inaccurate positioning, skipped steps, or complete axis failure.

This guide explains how to safely replace the motor on the Ray5 mini and miniS series. The overall procedure is similar for both X-axis and Y-axis motors, with slight structural differences between models.

1. Disconnect Components

• Disconnect the X/Y-axis motor cables
• Disconnect the laser module cable

2. Remove the Laser Module

• Loosen the M3×14 screws or L-shaped hand-tight screws
• Remove the laser module

 

Ray5 mini/miniS 2.5/3.5W 

Ray5 mini/miniS 5.5/10W

3. Remove Acrylic Covers (Ray5 miniS only)

If you are working on the Ray5 miniS, additional steps are required:

• Remove the right-side acrylic cover (8 screws)
• Remove the left-side acrylic cover (8 screws)
• Disconnect the door switch cable

⚠️ Important:

• Do not disconnect the emergency stop cable

 

Right-side acrylic cover 

Left-side acrylic cover 

Door switch

4. Remove Slider Components

• Use a 2mm hex wrench to loosen the four screws
• Remove:
  • Slider plastic part (mini)
  • Metal slider with plastic component (miniS)

 

Ray5 mini/miniS 2.5/3.5W 

Ray5 mini/miniS 5.5/10W

5. Remove the Motor

• Use a 2.5mm hex wrench to loosen the four motor screws
• Carefully remove the X/Y-axis motor

6. Install the New Motor

• Install the new motor in the correct orientation:

Ray5 mini

• X-axis motor connector → faces left
• Y-axis motor connector → faces backward

Ray5 miniS

• X-axis motor connector → faces left
• Y-axis motor connector → faces upward
• Ensure the timing belt is properly seated on the coupler
• Tighten all screws securely

 

7. Reinstall Slider Components

• Reinstall the slider plastic part or metal slider onto the X-axis bracket
• Ensure proper alignment and secure fastening

8. Reassemble (Ray5 miniS only)

• Reinstall the left and right acrylic covers
• Reconnect the door switch cable
• Ensure all components are properly secured

Mini:

MiniS:

Conclusion

Replacing the X/Y-axis motor on the Ray5 mini/miniS is a detailed but manageable maintenance task. By carefully following the correct steps and ensuring proper installation, you can restore precise motion control and maintain engraving accuracy.

Proper motor installation is essential for smooth operation, consistent engraving quality, and long-term machine stability.

Replacing the mainboard on a Ray5 mini or Ray5 miniS laser engraver may sound difficult, but the process is straightforward when performed carefully. This guide explains the exact replacement procedure from the official instructions while adding beginner-friendly explanations, safety precautions, troubleshooting advice, and maintenance tips to help you complete the repair successfully.

---

Table of Contents

1. What This Guide Covers
2. Quick Answer
3. Why This Process Matters
4. Before You Start
5. Requirements
6. Precautions
7. Step-by-Step Tutorial
8. Common Problems and Solutions
9. Tips for Better Results
10. Frequently Asked Questions
11. Final Thoughts

---

What This Guide Covers

This tutorial explains how to replace the mainboard on the Ray5 mini and Ray5 miniS laser engravers.

You will learn:

• How to safely access the mainboard
• Which cables must be disconnected
• How to reconnect the new board correctly
• How to align the TYPE-C and POWER ports
• How to avoid common installation mistakes
• Basic troubleshooting after replacement

The Ray5 mini and Ray5 miniS use the same mainboard, and the replacement procedure is similar. This guide uses the Ray5 mini X-axis as the example machine.

---

Quick Answer

To replace the Ray5 mini or miniS mainboard:

1. Remove the front beam cover using a 2.5 mm hex wrench.
2. Remove the existing mainboard.
3. Disconnect the X/Y motors, emergency stop, laser, and limit switch cables.
4. Connect all cables to the new mainboard using the original labels.
5. Install the new board, align the TYPE-C and POWER ports, and secure everything with screws.

Always power off the machine before starting maintenance.

---

Why This Process Matters

The mainboard is the control center of the laser engraver. It manages:

• Motor movement
• Laser control
• Limit switches
• Emergency stop functions
• USB communication
• Power distribution

If the mainboard becomes damaged or unstable, you may experience:

• Connection failures
• Random alarms
• Motor movement errors
• Laser output problems
• Machine startup issues
• Limit switch errors

Replacing the board correctly helps restore stable machine operation and prevents additional electrical issues.

---

Before You Start

Before opening the machine, prepare a clean workspace with enough lighting.

Make sure:

• The machine is powered off
• The power cable is disconnected
• The laser module is cool
• Small screws can be safely stored during disassembly

For the Ray5 miniS, you also need additional working space because the acrylic base plate must be removed during the process.

---

Requirements

Prepare the following tools and items before starting:

• 2.5 mm hex wrench
• 2.5 mm Allen wrench
• Replacement Ray5 mini/miniS mainboard
• Clean working surface
• Screw storage tray or container

Follow official machine specifications or instructions.

---

Precautions

Before replacing the Ray5 motherboard, carefully review these safety precautions.

Disconnect Power Completely

Always disconnect the machine from power before touching internal electronics. Working on a powered machine may damage the new mainboard.

Avoid Pulling on Wires

When disconnecting cables, pull gently from the connector housing instead of pulling the wires directly.

Keep Track of Cable Labels

The cables are labeled to match the corresponding ports on the mainboard. Incorrect connections may prevent the machine from operating properly.

Prevent Static Electricity

Avoid touching exposed electronic components unnecessarily. Static discharge can damage sensitive circuitry.

Organize Screws Carefully

The front beam cover and mainboard use multiple screws. Store them safely to avoid losing hardware during the repair.

---

Step-by-Step Tutorial

Step 1: Remove the Front Beam Cover

Action

Use a 2.5 mm hex wrench to loosen the four screws and remove the front beam cover.

For the Ray5 miniS, also remove the acrylic base plate to facilitate operation.

Expected Result

You should now have access to the internal mainboard compartment inside the front beam.

Important Notes

• Keep the screws organized for reinstallation.
• Do not force the cover if it feels stuck.
• Lift the cover carefully to avoid pulling internal cables.

 

Step 2: Remove the Mainboard

Action

Use a 2.5 mm Allen wrench to loosen the four screws and remove the mainboard.

Expected Result

The existing mainboard should now be free from the mounting position inside the beam.

Important Notes

• Support the board gently while removing screws.
• Do not bend the board during removal.
• Avoid touching exposed electronic components.

 

Step 3: Disconnect the Mainboard Cables

Action

Disconnect the following cables from the mainboard:

• X-axis motor (X)
• Y-axis motor (Y)
• Emergency stop (MS)
• Laser (PWM)
• X-axis limit switch (X-)
• Y-axis limit switch (Y-)

Expected Result

All required cables should now be disconnected from the old mainboard.

Important Notes

• Disconnect cables one at a time if needed.
• Double-check cable labels before removal.
• Never pull forcefully on connectors.

 

Step 4: Install the New Mainboard

Action

Connect the cables to the new mainboard, matching each cable label with the corresponding port on the mainboard.

Place the new mainboard inside the front beam, routing the cables through the gap near the Y-axis limit switch.

Make sure the TYPE-C and POWER ports at the front of the beam align correctly with the mainboard connectors.

Expected Result

The new mainboard should sit correctly inside the beam with all cables securely connected.

Important Notes

Cable Routing Matters

Improper cable routing may pinch wires when reinstalling the cover.

Verify Port Alignment

Before tightening screws, confirm:

• TYPE-C port alignment
• POWER port alignment

Misalignment may prevent proper cable connection later.

Check Cable Labels Carefully

The labels should match the ports exactly:

 

 

Step 5: Secure the Mainboard and Reinstall the Cover

Action

Use a 2.5 mm hex wrench and screws to secure the mainboard, then reinstall the cover.

This completes the mainboard replacement.

Expected Result

The machine should now be fully reassembled with the new mainboard installed.

Important Notes

• Tighten screws evenly.
• Do not overtighten screws.
• Confirm no cables are trapped beneath the cover.

 

 Mini:

MiniS:

Common Problems and Solutions

---

Tips for Better Results

Take Photos Before Disassembly

Photos help beginners remember cable positions and routing.

Label Connectors if Necessary

If cable labels are unclear, add temporary labels before disconnecting anything.

Work Slowly

Most installation mistakes happen when rushing the process.

Test Before Full Reassembly

After connecting the new board, verify the ports align properly before tightening everything completely.

Keep the Interior Clean

Dust and debris inside the beam can affect long-term reliability.

---

Frequently Asked Questions

Is the Ray5 mini mainboard the same as the Ray5 miniS mainboard?

Yes. The Ray5 mini and Ray5 miniS use the same mainboard, and the replacement procedure is similar.

---

Do I need special firmware after replacing the mainboard?

Follow official machine specifications or instructions.

---

Why do I need to remove the acrylic base plate on the miniS?

Removing the acrylic base plate provides easier access during the repair process.

---

What happens if I connect a cable to the wrong port?

Incorrect cable connections may cause movement errors, limit switch problems, or laser control issues. Always match cable labels carefully.

---

Can I replace the board without removing the front beam cover?

No. The front beam cover must be removed to access the mainboard.

---

What tool size is required for this repair?

The official instructions specify a 2.5 mm hex wrench and a 2.5 mm Allen wrench.

---

Why are the TYPE-C and POWER ports important during installation?

These ports must align correctly with the openings at the front of the beam so the machine can connect properly after reassembly.

---

What should I do if the machine still shows errors after replacement?

Recheck:

• Cable connections
• Port alignment
• Motor connectors
• Limit switch connectors
• Emergency stop cable

If problems continue, follow official machine specifications or instructions.

---

Final Thoughts

Replacing the Ray5 mini or Ray5 miniS mainboard is a manageable repair when performed carefully and methodically. The most important part of the process is reconnecting every cable correctly and ensuring the TYPE-C and POWER ports align properly during installation.

By following the official procedure exactly and taking your time during disassembly and reassembly, you can safely restore your laser engraver to normal operation. Proper cable management, organized screws, and careful connector handling will help prevent additional issues during the repair process.

For firmware, electrical specifications, or additional troubleshooting, follow official machine specifications or instructions.